Century Falcon 4 Plus Series Manuel d'utilisateur

User’s Manual Falcon 4 Plus/ Falcon 6 Plus Series

USB Interface Connector Type : Type B PIN NO. 1 2 3 4 FUNCTION VBUS D- D+ GND PS2 Interface PIN NO. 1 2 3 4 5 6 FUNCTION DATA N/C GND VCC

Applicator wafer Applicator module +5V 1 1+5V +24V 2 2+24V Printing (out) 3 3Printing

1-4. Printer Parts Appearance 4312 1. Control panel 2. Bottom Front Cover 3. Observing Window 4. Top Cover 1263457 1. Fan-Fold Label Insert 2. CF

Internal 123456712111098 1. Ribbon Rewind Shaft 2. Ribbon Supply Shaft 3. Printer Mechanism 4. Platen 5. Tear off Bar 6. Print Head Lever 7. Sens

Control Panel 23146759108 1. MEDIA LED 2. RIBBON LED 3. POWER LED 4. LCD 5. CANCEL Key 6. PAUSE Key 7. FEED Key 8. MINUS (-) Key (In

2. Printer Installation This printer model has the following print modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer th

5. Place the label roll onto the Label Roll Bar and align the label to printer’s inner wall. (To avoid the damage of media, please do not squeeze lab

9. Align the label edge inward, and fix the label outside in Label Guide. Adjust the Label Guide with the label. 【Note】 The Label should be put wi

2-2. Ribbon Installation 1. Place the printer on a horizontal surface, and open the top cover. 2. Follow the sequence and direction as the figure sh

5. Feed the ribbon from the Ribbon Supply Shaft under the print head. Wrap the ribbon around the Ribbon Rewind Shaft and stick it onto the empty ribb

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant

2-3. PC Connection 1. Please make sure the printer is powered off. 2. Take the power cable, plug the cable switch to the power socket, and then conn

2-4. Driver Installation 1. Once the USB cable is connected from PC to the printer, PC will automatically detect the new device and begin the install

3. Accessory 3-1. Internal Rewinder for Falcon 4 Plus 1 Rewinder 2 U Shape Clip 3 Screw x 4pcs 4 Rewind bracket 【Note】 Peel-off liner Max width: 11

3. Take off the U Shape Clip from the Liner Rewind Shaft. 4. Secure the Rewinder unit onto the printer. 12 5. After the Rewinder is installed, pl

3-2. Rewind Bracket Installation for Falcon 4 Plus 1. Face the printer front, and unscrew the bottom cover screw. 2. Remove the bottom front Cover.

8. Close the top cover to complete Label rewind bracket and Rewinder installation. 【Note1】 Before starting to rewind labels, please make sure the p

3-3. Stripper Installation for Falcon 4 Plus 1. Face the printer front, and unscrew clockwise the bottom front cover screw. 2. Remove the bottom fr

8. Wrap the liner around the Liner Rewinder Shaft, and use the U Shape Clip to secure the liner. 9. Flip the print head lever downward and then pus

3-4. Cutter Installation 1 Cutter Cover (Falcon 4 Plus) 2 Cutter Cover (Falcon 6 Plus) 3 Cutter 4 Locks 5 Screws x 2pcs 【Note1】 Do not cut self-adh

3. Hold the cutter and secure the cutter kit onto the printer. 4. Plug the cutter cable connector onto the cutter connector. 5. Tie the cables wit

Safety Instructions Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben. 1. Die Geräte nicht der Feuchtigkeit aussetzen. 2. Be

3-5. Parallel/PS2 Adapter Installation 1 Parallel Cable 2 Parallel/PS2 Adapter 3 Connector Cable 4 Screw x 2pcs 1234 1. Make sure the power is of

4. Align the Parallel/PS2 module to the parallel port and secure the module onto the back plate. 5. Connect one end of the 30 pin connector cable

3-6. Applicator Interface Installation 1 Applicator Interface 2 Screw x 2pcs 【Note】 This applicator interface is only applicable to THARO company’s

4. Plug the 10pin connector into the socket on mainborad that marked with “APP”. 5. Align the Applicator Interface to the hole and hold the positi

4. Control Panel 4-1. Control Panel Introduction Control keys FEED PAUSE CANCEL LED indicators Power Power on Ready(Power)After turning on the pow

Item Key Beep LCD Message Description Self test + Power on 3 beeps Self test Press and hold key and turn on the printer until the buzzer beeps 3

4-3. Setting mode In the Setting Mode, changes can be made according to requirement on the printing mode, options, media type, and parallel interface

LCD monitor Press and hold key about 3 to 4 seconds until the buzzer beep 3 times and LCD shows Setting mode. The LCD monitor will show different o

Sensor Setup Default: Gap paper Black Mark: for label or plain paper with black mark in the back Gap: for labels with liner and gap, or hang tags. T

Buzzer Setup Default: ON ON OFF Smart Backfeed Default: ON ON: This function must install stripper or cutter. OFF Password Default: OFF ON: When passw

Safety Instructions Please read the following instructions seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipme

The diagram of Setting Mode Printer PromptsIndefiniteFixedClock SettingClock DisplayEnter Keyboard?Recall LabelSelect LabelPrint QuantityPrinting M

4-4. Self-Test The Self-Test function will help user to check whether the printer is operating normally. In Self-Test Mode, the printer will print out

4-5. Dump Mode When label setting and the print result don’t match, it’s recommended to go into the Dump Mode to check whether there’s a mistake in da

4-7. Error Messages If problems occur that prevent the printer printing normally, the printer will beep as warning, and error messages will be display

Memory Full 2 beeps twice Memory is full Delete unnecessary data in the memory or use CF Card. Rewinder Full 2 beeps twice Rewinder is full Rem

5. Maintenance and Adjustment 5-1. Print Head Module Installation / Removal Instruction 1. Open the top cover. 【Note】 Power-off when removing print

5-2. TPH Print Line Adjustment Please contact your local dealer for technical support 1. Open the top cover. 2. Pull the Print Head Lever out and

5-3. Ribbon Tension Adjustment The ribbon shaft tension can be adjusted by turning the ribbon shaft knob clockwise or counterclockwise. There are 4 di

5-4. Thermal Print Head Cleaning Unclear printouts (some parts of label cannot be printed) may be caused by dusty print head, ribbon stain, or label l

5-5. Print Head Balance and Pressure Adjustment 1. Open the top cover. 2. Pull the Print Head Lever out and flip it upward to the right. 21 Falcon

1. BARCODE PRINTER... 5 1-1. Printer Accessories...

5-6. Ribbon Shield Adjustment 1. Due to the differences in the ribbon materials, if ribbon wrinkles occur during printing, please adjust the ribbon

5-7. Adjust the Cutter 1. The cutter-adjusting hole is on both sides of cutter. 2. The cutter will not work properly if there is a paper jam. Pleas

5-9. Troubleshooting Problem Recommended Solution LCD Display shows no message after power on the printer  Check the power cable LED light indicates

1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and store appropriately.  Bar

Resident Fonts 11 resident Windows bit mapped fonts (6,8,10,12,14,18,24,30,16X26,OCR A & B); can be rotated in 8 orientations and expandable 8 tim

Ribbon Length: 450 m (1471 ft) Type: transfer ribbons (wax, hybrid, and resin) in widths of 60 to 174 mm (2.36” to 6.85”). Auto ink inside and ink out

1-3. Communication Interface Parallel Interface Handshake : DSTB connects to the printer, BUSY connects to the host Interface cable : Parallel cab