4118590 Amp Flux Wire WelderInstruction ManualNeed help with your new arc welder?Call our customer service hotline at 1-800-386-0191SAVE THESE INSTRUC
GroundedOutlet BoxGroundedOutletPlugGrounding Plug120 Volt 20 Amp Dedicated Circuit RequiredMANUALExplosion ElectricShockFlyingSparksRays BurnsFire Fu
MetalThicknessOutput CurrentSettings (Amps)18 - 14 Gauge LOW (64A)HIGH (90A)Thicker than 14 GaugeNOTE: Above settings are intended to serve as a gener
Direction of travelWork PieceWork PieceWire LengthTo Work PieceWire Electrode1/4" MoltenSlagShieldingGasesGas Nozzle.030"/.035"(0.8mm)G
WELDING GUIDELINESLEARNING TO WELDWelding is a skill that requires practice and, like any new skill, cannot be mastered without experience. The follow
76211 Work Piece2 Work ClampGas NozzleSolid Wire Electrode567Solidified SlagWelding Hammer/Brush4Mig Torch3435SHIELDED METAL ARC WELDING SETUP14
STRIKING AN ARC1) Be sure the work clamp is properly attached to the work piece. 2) Position gun over joint to be welded. The end of the wire may ligh
Travel angle is the angle in the line of welding and may vary from 5º to 45º from the vertical, depending upon weldingconditions and technique require
SLAG REMOVALGroundedOutlet BoxGroundedOutletPlugGrounding Plug120 Volt 20 Amp Dedicated Circuit RequiredMANUALExplosion ElectricShockFlyingSparksRays
No weld output; wire does not feed; fan does not run.Problem EncounteredPossible CauseCorrective ActionNo weld output; wire doesnot feed; fan continue
19Bead is intermittently too thin or too thick.Problem EncounteredPossible CauseCorrective ActionRagged depressions at edge of weld.Weld bead does not
SAFETY BEGINS WITH YOUIt is the owner and/or operator’s responsibility to study all WARNINGS, operating, and maintenance instructions contained on the
ONE YEAR LIMITED WARRANTY - STAR ASIA-USA, LLC ELECTRIC ARC WELDERSStar Asia-USA, LLC (hereinafter “seller”) warrants to the original purchaser only,
21Distributed by Star Asia-USA, LLCP.O. Box 58399, Renton, WA 98058Consumer Service: 800-386-0191e-mail: [email protected]©2005 Star Asia-USA, LLC
GroundedOutlet BoxGroundedOutletPlugGrounding Plug120 Volt 20 Amp Dedicated Circuit RequiredMANUALExplosion ElectricShockFlyingSparksRays BurnsFire Fu
IMPORTANT SAFETY RULES - FOR ARC WELDERSSAVE THESE INSTRUCTIONSARC Welding can be hazardous. Protect yourself and others from possible serious injury
• Do not drape cables over your body.• If earth grounding of the workpiece is required, ground it directly with a separate cable.• Do not allow any pa
HOT PARTS can cause severe burns!• Never touch hot parts bare handed.• Allow adequate cooling period before touching work piece.MAGNETIC FIELDS can
GroundedOutlet BoxGroundedOutletPlugGrounding Plug120 Volt 20 Amp Dedicated Circuit RequiredMANUALExplosion ElectricShockFlyingSparksRays BurnsFire Fu
SPECIFICATIONS:Type: 90 Amp gasless ux-core wire welderInput Voltage: 120 Volt (1~60Hz)Rated Output: 90 Amps @ 10% Duty CycleOutput
1) Verify that welder is turned OFF and is disconnected from the power source.2) Unlock top cover panel and lift cover back to expose wire feed mechan
Commentaires sur ces manuels